Questo sito web utilizza i cookie. Utilizzando questo sito, acconsenti all'utilizzo dei cookie. Per ulteriori informazioni, dai un'occhiata al nostro politica sulla riservatezza.

Le immagini servono solo come riferimento,

Vedi Specifiche Tecniche

MAX2992GCB+T +BOM

Advanced power line communication solution for industrial automation applications

Produttore:

Maxim Integrated
ProduttorePart #:

MAX2992GCB+T
Scheda dati:

MAX2992GCB+T Scheda dati (PDF)
Pin Count:

64
Released Date:

Jan 17, 2021
Last Modified Date:

Mar 7, 2023 4:10 PM UTC
EDA/CAD Modelli:

Richiedi modelli CAD gratuiti per MAX2992GCB+T

MAX2992GCB+T Descrizione generale

The MAX2992 powerline communication (PLC) baseband modem delivers half-duplex, asynchronous data communication over AC power lines at speeds up to 300kbps (full FCC band data rate). The MAX2992 is a system-on-chip (SoC) that combines the physical (PHY) and media access control (MAC) layers using Maxim's 32-bit MAXQ30 microcontroller core. The MAX2991 integrated analog front-end transceiver interfaces seamlessly with the MAX2992, and together with the MAX2992 G3-PLC firmware, forms a complete G3-PLC-compliant modem solution. The MAX2992 utilizes OFDM techniques with DBPSK, DQPSK, D8PSK modulation and forward error correction (FEC) to enable robust data communication using the electrical power grid. The design provides inherent adaptability to frequency selective channels, robustness in the presence of group delay, and immunity to impulsive noise. To allow for regulatory compliance, the MAX2992 incorporates a programmable tone notching mechanism. This allows the notching of certain frequency bands in the transmit spectrum of the modem. This feature also provides an alternative method to address coexistence with other narrowband transmitters such as legacy FSK-based PLC systems. The MAX2992 MAC incorporates a 6LoWPAN adaptation layer to support IPv6 packets. An enhanced CSMA/CA and ARQ, together with the mesh routing protocol, supports all common MAC layer services for various network topologies. Intelligent communication mechanisms adapt and enhance system performance over a range of channel conditions. These mechanisms include channel estimation, adaptive tone mapping, and routing protocols. An on-chip CCM (an extension of CCM specified in IEEE 802.15.4) authentication coprocessor with AES-128 encryption/decryption provides security and authentication.

Caratteristiche principali

G3-PLC Compliant
Prestandard Conformance: IEEE
Frequency-Band Compliant with CENELEC, FCC, and ARIB
Operating Frequency from 10kHz to 490kHz
Single-Chip Solution Integrating Physical Layer (PHY) and Media Access Controller (MAC)
Two UART and Two SPI Interfaces
Supports IPV6-Compatible Networking Layer
6LoWPAN IPV6 Header Compression Maximizes Payload Size
Dynamic Routing Mechanism Supports Mesh Networking
CSMA/CA (Carrier Sense Multiple Access with Collision Avoidance/Channel Access)
High-Speed, Reliable Communication
Data Rate of up to 300kbps
Two Layers of Forward Error Correction (FEC) and Cyclic Redundancy Check (CRC16)
Enhanced FEC with Reed-Solomon and Viterbi
CCM Authentication Coprocessor featuring AES-128 Encryption/Decryption
Automatic Repeat Request (ARQ) Enhances Error Detection and Data Reliability
Dynamic Link Adaptation to Select Optimum Data Rate Based on Channel Condition
Programmable Tone Notching
AEC-Q100 Automotive Qualified

Applicazione

Advanced Metering Infrastructure (AMI)
AMI Concentrators
Building Automation
Electronic Vehicle Charging
Home Energy Monitoring
Smart Grid Communications
Smart Meters
Solar and Renewable Energy Management
Street Lighting Automation

Specifiche

Pin Count	64	Released Date	Jan 17, 2021
Last Modified Date	Mar 7, 2023 4:10 PM UTC

Politiche di servizio e altro

Relativi al servizio post-vendita e alla liquidazione

Pagamento

Metodo di pagamento

TT/bonifico bancario

PayPal

Western Union

Grammo dei soldi

Per canali di pagamento alternativi, contattaci a:

[email protected]

Spedizione e imballaggio

metodo di spedizione

Fedex

UPS

DHL

NTN

Imballaggio

AVAQ determina e confeziona tutti i dispositivi in base ai requisiti di protezione contro le scariche elettrostatiche (ESD) e il livello di sensibilità all'umidità (MSL)..