Questo sito web utilizza i cookie. Utilizzando questo sito, acconsenti all'utilizzo dei cookie. Per ulteriori informazioni, dai un'occhiata al nostro politica sulla riservatezza.

Le immagini servono solo come riferimento,

Vedi Specifiche Tecniche

TDA8007BHLBE +BOM

Smart Card Interface 10MHz 3.3V/5V 700mW 48-Pin LQFP

Produttore:

NXP Semiconductor
ProduttorePart #:

TDA8007BHLBE
Scheda dati:

TDA8007BHLBE Scheda dati (PDF)
Interface:

Parallel
Voltage - Supply:

2.7V ~ 6V
Mounting Type:

Surface Mount
Base Product Number:

TDA800
EDA/CAD Modelli:

Richiedi modelli CAD gratuiti per TDA8007BHLBE

E-mail: [email protected]

Skype: live:.cid.ab6b29428937b76

tel: +852 95804164

TDA8007BHLBE Descrizione generale

The TDA8007BHL is a cost-effective card interface for dual smart card readers. Controlled through a parallel bus, it meets all requirements of ISO 7816, GSM 11-11, EMV4.2 and EMV 2000. It is addressed on a non-multiplexed 8-bit databus, by means of address registers AD0, AD1, AD2 and AD3. TDA8007BHL/C3 can be also addressed through a multiplexed access. The integrated ISO UART and the time-out counters allow easy use even at high baud rates with no real time constraints. Due to its chip select, external input/output and interrupt features, it greatly simplifies the realization of a reader of any number of cards. It gives the cards and the reader a very high level of security, due to its special hardware against ESD, short-circuiting, power failure, etc. The integrated step-up converter allows operation within a supply voltage range of 2.7 V to 6 V.

TDA8007BHL/C4 supports only non multiplex access and TDA8007BHL/C3 support both non multiplexed and multiplexed access.

Caratteristiche principali

Control and communication through an 8-bit parallel interface, compatible with non-multiplexed memory access, TDA8007BHL/C3 can be also addressed through a multiplexed memory access
Specific ISO UART with parallel access input/output for automatic convention processing, variable baud rate through frequency or division ratio programming, error management at character level for T = 0 and extra guard time register
FIFO for 1 to 8 characters in reception mode
Parity error counter in reception mode and in transmission mode with automatic re-transmission
Dual VCC generation: 5 V ± 5 %, 65 mA (max.); 3 V ± 8 %, 50 mA (max.) or 1.8 V ± 10 %, 30 mA (max.); with controlled rise and fall times
Dual cards clock generation (up to 10 MHz), with three times synchronous frequency doubling (fXTAL, 1/2fXTAL, 1/4fXTAL and 1/8fXTAL)
Cards clock stop (at high or low level) or 1.25 MHz (from internal oscillator) for cards Power-down mode
Automatic activation and deactivation sequence through an independent sequencer
Supports the asynchronous protocols T = 0 and T = 1 in accordance with: ISO 7816 and EMV4.2
Versatile 24-bit time-out counter for Answer To Reset (ATR) and waiting times processing
Specific Elementary Time Unit (ETU) counter for Block Guard Time (BGT): 22 in T = 1 and 16 in T = 0
Minimum delay between two characters in reception mode:
in Protocol T = 0: 11.8 ETU
in Protocol T = 1: 10.8 ETU
Supports synchronous cards
Current limitations in the event of short-circuit (pins I/O1, I/O2, VCC1, VCC2, RST1 and RST2)
Special circuitry for killing spikes during power-on/power-off
Supply supervisor for power-on/power-off reset
Step-up converter (supply voltage from 2.7 V to 6 V), doubler, tripler or follower according to VCC and VDD
Additional input/output pin allowing use of the ISO UART for another analog interface (pin I/OAUX)
Additional interrupt pin allowing detection of level toggling on an external signal (pin INTAUX)
Fast and efficient swapping between the three cards due to separate buffering of parameters for each card
Chip select input allowing use of several devices in parallel and memory space paging
Enhanced ESD protections on card side (except C4x, C8x): 6 kV (min.)
Software library for easy integration within the application
Power-down mode for reducing current consumption when no activity.
Target Applications
Multiple smart card readers for multiprocessor applications (EMV banking, digital payTV and access control, etc.).

Specifiche

Category	Integrated Circuits (ICs)InterfaceSpecialized	Series	-
Applications	-	Interface	Parallel
Voltage - Supply	2.7V ~ 6V	Mounting Type	Surface Mount
Base Product Number	TDA800

Politiche di servizio e altro

Relativi al servizio post-vendita e alla liquidazione

Pagamento

Metodo di pagamento

TT/bonifico bancario

PayPal

Western Union

Grammo dei soldi

Per canali di pagamento alternativi, contattaci a:

[email protected]

Spedizione e imballaggio

metodo di spedizione

Fedex

UPS

DHL

NTN

Imballaggio

AVAQ determina e confeziona tutti i dispositivi in base ai requisiti di protezione contro le scariche elettrostatiche (ESD) e il livello di sensibilità all'umidità (MSL)..