Questo sito web utilizza i cookie. Utilizzando questo sito, acconsenti all'utilizzo dei cookie. Per ulteriori informazioni, dai un'occhiata al nostro Privacy Policy.

Le immagini servono solo come riferimento,

Vedi Specifiche Tecniche

O9039A389IZWSTQ1 +BOM

Power Management Multi-Channel IC to Automotive AEC-Q100 169-Pin NFBGA T/R

Produttore:

Texas Instruments, Inc
ProduttorePart #:

O9039A389IZWSTQ1
Scheda dati:

O9039A389IZWSTQ1 Scheda dati (PDF)
genericPartNumber:

TPS659039-Q1
partDescription:

Automotive 3.135-V to 5.25-V, 7 buck & 6-LDO PMIC for ARM Cortex-A15 processors
EDA/CAD Modelli:

Richiedi modelli CAD gratuiti per O9039A389IZWSTQ1

E-mail: [email protected]

Skype: live:.cid.ab6b29428937b76

tel: +852 95804164

O9039A389IZWSTQ1 Descrizione generale

The TPS659038-Q1 and TPS659039-Q1 devices are integrated power-management integrated circuits (PMICs) for automotive applications. The device provides seven configurable step-down converters with up to 6 A of output current for memory, processor core, input-output (I/O), or preregulation of LDOs. One of these configurable step-down converters can be combined with another 3-A regulator to allow up to 9 A of output current. All of the step-down converters can synchronize to an external clock source between 1.7 Mhz and 2.7 MHz, or an internal fall back clock at 2.2 MHz. The TPS659038-Q1 device contains 11 LDO regulators while the TPS659039-Q1 device contains six LDO regulators for external use. These LDO regulators can be supplied from either a system supply or a preregulated supply. The power-up and power-down controller is configurable and supports any power-up and power-down sequences (OTP based). The TPS659038-Q1 and TPS659039-Q1 devices include a 32-kHz RC oscillator to sequence all resources during power up and power down. In cases where a fast start up is needed, a 16-MHz crystal oscillator is also included to quickly generate a stable 32-kHz for the system. All LDOs and SMPS converters can be controlled by the SPI or I²C interface, or by power request signals. In addition, voltage scaling registers allow transitioning the SMPS to different voltages by SPI, I²C, or roof and floor control. One dedicated pin in each package can be configured as part of the power-up sequence to control external resources. General-purpose input-output (GPIO) functionality is available and two GPIOs can be configured as part of the power-up sequence to control external resources. Power request signals enable power mode control for power optimization. The device includes a general-purpose (GP) sigma-delta analog-to-digital converter (ADC) with three external input channels. The TPS659038-Q1 and TPS659039-Q1 device is available in a 13-ball × 13-ball nFBGA package with a 0,8-mm pitch.

Caratteristiche principali

Qualified for Automotive Applications
- AEC-Q100 Qualified With the Following Results:
  - Temperature Grade 3: –40°C to 85°C
  - ESD Classification:
    - HBM Level 2
    - CDM Level C3
  - Latch-Up Classification:
    - Level IIB for I²C and SPI Terminals
    - Level IIA for all other Terminals
Seven Step-Down Switched-Mode Power Supply (SMPS) Regulators:
- One 0.7 to 1.65 V at 6 A (10-mV Steps)
  - Dual-Phase Configuration With Digital Voltage Scaling (DVS) Control
- One 0.7 to 1.65 V at 4 A (10-mV Steps)
  - Dual-Phase Configuration With DVS Control
- One 0.7 to 3.3 V at 3 A (10 or 20-mV Steps)
  - Single-Phase Configuration
  - This Regulator can be Combined With the 6 A Resulting in a 9 A Triple-Phase Regulator (DVS Controlled)
- Two 0.7 to 3.3 V at 2 A (10 or 20-mV Steps)
  - Single-Phase Configuration
  - One Regulator With DVS Control, Which can also be Configured as a 3-A Regulator
- Two 0.7 to 3.3 V at 1 A (10 or 20-mV Steps)
  - Single-Phase Configuration
  - One Regulator With DVS Control
- Output Current Measurement in All Except 1-A SMPS Regulators
- Differential Remote Sensing (Output and Ground) in Dual-Phase and Triple-Phase Regulators
- Hardware and Software-Controlled ECO-mode™ up to 5 mA with 15-µA Quiescent Current
- Short-Circuit Protection
- Powergood Indication (Voltage and Overcurrent Indication)
- Internal Soft-Start for In-Rush Current Limitation
- Ability to synchronize SMPS to External Clock or Internal Fallback Clock With Phase Synchronization
Eleven General-Purpose Low Dropout (LDO) Regulators (50-mV Steps):
- Four 0.9 to 3.3 V at 300 mA With Preregulated Supply
- Four 0.9 to 3.3 V at 200 mA With Preregulated Supply
- One 0.9 to 3.3 V at 50 mA With Preregulated Supply
- One 100-mA USB LDO
- One Low-Noise LDO 0.9 to 3.3 V up to 100 mA (Low Noise Performance up to 50 mA)
- Two Additional LDOs for PMU Internal Use
- Short-Circuit Protection
Clock Management 16-MHz Crystal Oscillator and 32-kHz RC Oscillator
- One Buffered 32-kHz Output
Real-Time Clock (RTC) With Alarm Wake-Up Mechanism
12-bit Sigma-Delta General-Purpose Analog-to-Digital-Converter (GPADC) With Three External Input Channels and Six Internal Channels for Self Monitoring
Thermal Monitoring
- High Temperature Warning
- Thermal Shutdown
Control
- Configurable Power-Up and Power-Down Sequences (One-Time Programmable [OTP])
- Configurable Sequences Between the SLEEP and ACTIVE States (OTP Programmable)
- One Dedicated Digital Output Signal (REGEN) that can be Included in the Start-up Sequence
- Three Digital Output Signals MUXed With GPIO that can be Included in the Start-up Sequence
- Selectable Control Interface
  - One Serial Peripheral Interface (SPI) for Resource Configurations and DVS Control
  - Two I²C Interfaces. One Dedicated for DVS Control, and a General Purpose I²C Interface for Resource Configuration and DVS Control
Undervoltage Lockout
System Voltage Range from 3.135 to 5.25 V
Package Options
- 12-mm × 12-mm 169-pin nFBGA with 0,8-mm Ball Pitch

Specifiche

genericPartNumber	TPS659039-Q1	orderablePartNumber	O9039A389IZWSTQ1
partDescription	Automotive 3.135-V to 5.25-V, 7 buck & 6-LDO PMIC for ARM Cortex-A15 processors	statusDisplay	ACTIVE
statusDescription	This product has been released to the market and is available for purchase. For some products, newer alternatives may be available.

Politiche di servizio e altro

Relativi al servizio post-vendita e alla liquidazione

Pagamento

Metodo di pagamento

TT/bonifico bancario

PayPal

Western Union

Grammo dei soldi

Per canali di pagamento alternativi, contattaci a:

[email protected]

Spedizione e imballaggio

metodo di spedizione

Fedex

UPS

DHL

NTN

Imballaggio

AVAQ determina e confeziona tutti i dispositivi in base ai requisiti di protezione contro le scariche elettrostatiche (ESD) e il livello di sensibilità all'umidità (MSL)..