Questo sito web utilizza i cookie. Utilizzando questo sito, acconsenti all'utilizzo dei cookie. Per ulteriori informazioni, dai un'occhiata al nostro politica sulla riservatezza.

Le immagini servono solo come riferimento,

Vedi Specifiche Tecniche

DS2433 +BOM

4Kb 1-Wire EEPROM

Produttore:

MAXIM
ProduttorePart #:

DS2433
Scheda dati:

DS2433 Scheda dati (PDF)
Part Life Cycle Code:

Transferred
Clock Frequency-Max (fCLK):

0.0163 MHz
Endurance:

100000 Write/Erase Cycles
JESD-30 Code:

O-PBCY-T3
EDA/CAD Modelli:

Richiedi modelli CAD gratuiti per DS2433

E-mail: [email protected]

Skype: live:.cid.ab6b29428937b76

tel: +852 95804164

DS2433 Descrizione generale

The DS2433 4Kb 1-Wire® EEPROM identifies and stores relevant information about the product to which it is associated. This lot or product specific information can be accessed with minimal interface, for example a single port pin of a microcontroller. The DS2433 consists of a factory-lasered registration number that includes a unique 48-bit serial number, an 8-bit CRC, and an 8-bit Family Code (23h) plus 4096 bits of user-programmable EEPROM. The power to read and write the DS2433 is derived entirely from the 1-Wire communication line. The memory is organized as sixteen pages of 256 bits each. The scratchpad is an additional page that acts as a buffer when writing to memory. Data is first written to the scratchpad where it may be read back for verification. A copy scratchpad command will then transfer the data to memory. This process insures data integrity when modifying the memory. The 64-bit registration number provides a guaranteed unique identity which allows for absolute traceability and acts as node address if multiple DS2433s are connected in parallel to form a local network. Data is transferred serially via the 1-Wire protocol which requires only a single data lead and a ground return. The PR-35 and SO packages provide a compact enclosure that allows standard assembly equipment to handle the device easily for attachment to printed circuit boards or wiring. Typical applications include storage of calibration constants, board identification and product revision status.

Caratteristiche principali

4096 Bits Electrically Erasable Programmable Read-Only Memory (EEPROM)
Unique, Factory-Lasered and Tested 64-Bit Registration Number (8-Bit Family Code + 48-Bit Serial Number + 8-Bit CRC Tester) Assures Absolute Identity Because No Two Parts Are Alike
Built-In Multidrop Controller Ensures Compatibility with Other MicroLAN Products
Memory Partitioned Into Sixteen 256-Bit Pages for Packetizing Data
256-Bit Scratchpad with Strict Read/Write Protocols Ensures Integrity of Data Transfer
Reduces Control, Address, Data, and Power to a Single Data Pin
Directly Connects to a Single Port Pin of a Microprocessor and Communicates at Up to 16.3kbps
Overdrive Mode Boosts Communication Speed to 142kbps
8-Bit Family Code Specifies DS2433 Communication Requirements to Reader
Presence Detector Acknowledges When Reader First Applies Voltage
Low-Cost PR-35, SFN, Flip Chip, or 8-Pin SO Surface-Mount Packages
Reads and Writes Over a Wide Voltage Range of 2.8V to 6.0V from -40°C to +85°C

Applicazione

Device Authentication
IEEE 1451.4 Sensor TEDS
Ink/Toner Cartridges
Medical Sensors
PCB Identification
Self-Configuration of Central Office Switches, Wireless Base Stations, PBXs, or other Modular-Based Rack Systems

Specifiche

Part Life Cycle Code	Transferred	Reach Compliance Code
Clock Frequency-Max (fCLK)	0.0163 MHz	Endurance	100000 Write/Erase Cycles
JESD-30 Code	O-PBCY-T3	JESD-609 Code	e0
Memory Density	4096 bit	Memory IC Type	EEPROM
Memory Width	8	Number of Functions	1
Number of Terminals	3	Number of Words	512 words
Number of Words Code	512	Operating Mode	SYNCHRONOUS
Operating Temperature-Max	85 °C	Operating Temperature-Min	-40 °C
Organization	512X8	Parallel/Serial	SERIAL
Qualification Status	Not Qualified	Serial Bus Type	1-WIRE
Supply Voltage-Max (Vsup)	6 V	Supply Voltage-Min (Vsup)	2.8 V
Surface Mount	NO	Technology	CMOS
Temperature Grade	INDUSTRIAL	Terminal Finish	Tin/Lead (Sn/Pb)
Terminal Form	THROUGH-HOLE	Terminal Pitch	1.27 mm
Terminal Position	BOTTOM

Politiche di servizio e altro

Relativi al servizio post-vendita e alla liquidazione

Pagamento

Metodo di pagamento

TT/bonifico bancario

PayPal

Western Union

Grammo dei soldi

Per canali di pagamento alternativi, contattaci a:

[email protected]

Spedizione e imballaggio

metodo di spedizione

Fedex

UPS

DHL

NTN

Imballaggio

AVAQ determina e confeziona tutti i dispositivi in base ai requisiti di protezione contro le scariche elettrostatiche (ESD) e il livello di sensibilità all'umidità (MSL)..