Questo sito web utilizza i cookie. Utilizzando questo sito, acconsenti all'utilizzo dei cookie. Per ulteriori informazioni, dai un'occhiata al nostro politica sulla riservatezza.

Le immagini servono solo come riferimento,

Vedi Specifiche Tecniche

BCM4330XKUBG +BOM

BCM4330XKUBG Telecom Circuit designed with 133-pin WLBGA package

Produttore:

BROADCOM
ProduttorePart #:

BCM4330XKUBG
Scheda dati:

BCM4330XKUBG Scheda dati (PDF)
Part Life Cycle Code:

Transferred
Reach Compliance Code:

compliant
HTS Code:

8542.39.00.01
JESD-30 Code:

R-PBGA-B133
EDA/CAD Modelli:

Richiedi modelli CAD gratuiti per BCM4330XKUBG

Caratteristiche principali

IEEE 802.11x Key Features
Single-band 2.4 GHz 802.11 b/g/n or dual
band 2.4 GHz and 5 GHz 802.11 a/b/g/n (non
simultaneous)
Single stream 802.11n support for 20 MHz
channels provides PHY layer rates up to MCS7
(72 Mbps) for typical upper-layer throughput
in excess of 45 Mbps.
Integrated CMOS power amplifiers with
internal power-detectors and closed-loop
power control can deliver greater than
18 dBm of linear output power (in 2.4 GHz
band).
PAs can be powered directly from VBAT,
eliminating the need for a PALDO.
Up to 8 RF control signals are available to
support optional external PAs for higher
output power and LNAs for enhanced
sensitivity.
Supports a single 2.4 GHz antenna shared
between WLAN and Bluetooth.
Shared Bluetooth and WLAN receive signal
path eliminates the need for an external
power splitter while maintaining excellent
sensitivity for both Bluetooth and WLAN.
Internal fractional nPLL allows support for a
wide range of reference clock frequencies
Supports IEEE 802.15.2 external three-wire
coexistence scheme to optimize bandwidth
utilization with other co-located wireless
technologies such as GPS, WiMax, or UWB
Supports standard SDIO v2.0 (50 MHz, 4-bit
and 1-bit), and gSPI (48 MHz) host interfaces.
Alternative host interface supports HSIC (a
USB 2.0 derivative for short-distance, on
board connections).
Integrated ARM® Cortex-M3 processor and
on-chip memory for complete WLAN
subsystem functionality, minimizing the need
to wake up the applications processor for
standard WLAN functions. This allows for
further minimization of power consumption,
while maintaining the ability to field upgrade
with future features.
OneDriver™ software architecture for easy
migration from existing embedded WLAN and
Bluetooth devices as well as future devices.
Bluetooth and FM Key Features
Bluetooth Core Specification Version 4.0 + HS compliant
with provisions for supporting future specifications
Bluetooth Class 1 or Class 2 transmitter operation
Supports extended Synchronous Connections (eSCO), for
enhanced voice quality by allowing for retransmission of
dropped packets
Adaptive Frequency Hopping (AFH) for reducing radio
frequency interference
Interface support—Host Controller Interface (HCI) using
a high-speed UART interface and PCM for audio data
The FM unit supports HCI for communication, stereo
analog input and output
Low-power consumption improves battery life of
handheld devices
FM receiver: 65 MHz to 108 MHz FM bands; supports the
European Radio Data Systems (RDS) and the North
American Radio Broadcast Data System (RBDS) standards
Supports multiple simultaneous Advanced Audio
Distribution Profiles (A2DP) for stereo sound
Automatic frequency detection for standard crystal and
TCXO values
FM transmitter: 65 MHz to 108 MHz bands; supports
both RDS and the RBDS standards and programmable
output power.
General Features
Supports battery voltage range from 2.3V to 4.8V
supplies with internal switching regulator
Programmable dynamic power management
2 Kbit OTP for storing board parameters
Package options:
- 144 ball FCFBGA (6.5 mm x 6.5 mm, 0.5 mm pitch)
- 133 ball WLBGA (4.89 mm x 5.33 mm, 0.4 mm pitch)
- 225 bump WLCSP (4.89 mm x 5.33 mm, 0.2 mm
pitch)
Security:
- WPA™- and WPA2™- (Personal) support for powerful
encryption and authentication
- AES and TKIP in hardware for faster data encryption
and 802.11i compatibility
- Reference WLAN subsystem provides
Cisco® Compatible Extension- (CCX,
CCX 2.0, CCX 3.0, CCX 4.0, CCX 5.0) certified
- Reference WLAN subsystem provides Wi-Fi
Protected Setup (WPS)
Worldwide regulatory support: Global products
supported with worldwide homologated design

Specifiche

Part Life Cycle Code	Transferred	Reach Compliance Code	compliant
HTS Code	8542.39.00.01	JESD-30 Code	R-PBGA-B133
Length	5.33 mm	Number of Functions	1
Number of Terminals	133	Operating Temperature-Max	85 °C
Operating Temperature-Min	-30 °C	Seated Height-Max	0.55 mm
Supply Voltage-Nom	1.2 V	Surface Mount	YES
Telecom IC Type	TELECOM CIRCUIT	Temperature Grade	OTHER
Terminal Form	BALL	Terminal Pitch	0.4 mm
Terminal Position	BOTTOM	Width	4.89 mm

Politiche di servizio e altro

Relativi al servizio post-vendita e alla liquidazione

Pagamento

Metodo di pagamento

TT/bonifico bancario

PayPal

Western Union

Grammo dei soldi

Per canali di pagamento alternativi, contattaci a:

[email protected]

Spedizione e imballaggio

metodo di spedizione

Fedex

UPS

DHL

NTN

Imballaggio

AVAQ determina e confeziona tutti i dispositivi in base ai requisiti di protezione contro le scariche elettrostatiche (ESD) e il livello di sensibilità all'umidità (MSL)..